(216) 990-0563
Anderson Lasers, Inc
  • Main Page
  • New Arrivals
  • Contact Us
  • Laser Systems
    • Industrial Lasers
    • Scientific Research Lasers
  • Optical Test & Measurement Equipment
  • Laser & Optical Components
  • Electronic Test Equipment
  • Miscellaneous Scientific Instruments
  • Accessories
  • Vacuum Equipment
  • Unusual Items

Lumonics JK 700/ Lumonics JK-706 1000 watt welder

Very rare Lumonics JK-706 laser welder, rated 1000 watts will produce 1200 watts. Pulse widths from 500 micro-seconds to 20 milliseconds, with a max 105 joules per pulse, and a maximum rep rate of 500 pulse per second, and pulse shaping up to 20 segments. This system was manufactured for Westinghouse. The laser system is in excellent condition, and before de-commission was checked out by Lumonics. It comes with a 3 month warranty. This system has full set of manuals, schematics, beam delivery head, long armored fiber on reel Price.....................Call for Pricing

Micromachining system, MM5800 dual beam

by ESI-ESI MM5800 micromachining system employing two IPG 700 watt fiber lasers single mode, with twin Laser Mech beam delivery. This machine is capable of 2500 holes per second, was set up for drilling/cutting .030" (750 micron) aluminum with .012" (300 micron) holes. Can be used for any machining drilling or marking. Has twin cameras, both wide, and fine, with micron accuracy. System was never in service only used for some testing. Looks new with low hours. Cutting bed 533mm x 635mm, with "z axis of 40mm. See spec page below. Price...........call for pricing.

Coherent/Deos Gem 100

Coherent Gem 100L, manufactured 2008, rated 100 watts, producing 125-130 watts, using a Synrad controller. Excellent condition, comes with manual, power supply, and controller fully operational. Power supply requires 220 volt single phase, no dc supply to mess with. Price.....call for pricing

Spectra Physics UV-355 Tristar-1000

Spectra Physics diode pumped Tristar 1000 laser system producing 840mw, not optimized, but near spec. power. Q-switched 355nm laser system pictures taken in operation at 20Khz. Better pictures to follow. Unit is in very good condition.Price......call for pricing.

A.E.C 8.5 ton air cooled chiller

In excellent condition with low usage, manual, 220 volt 3 phase. See Spec. page below. Price...call for pricing

Coherent D-62, 80 watt, Co2 laserNew, unused

Excellent condition with manual, manufactured in 1996, new unused laser system. Price....call for pricing

Trumph Haas H-703 D Laser

Has twin energy share module output. More info to follow. Price....Call for pricing

Yamabishi Auto Volt 25KW 3 Phase  power regulator

Yamabishi 25 Kw power regulator. Input from 170-230 volt, output 220 volt. Two units available. Price...Call for pricing

Synrad 48-2 CO2 laser

Comes with built in 120 vac. power supply, just plug it in the wall. Has less than 10 hours use on it. Excellent condition Price......Call for pricing

Lumonics JK-701h 550 watt Yag with twin energy share module

Just arrived 2 JK-701h 550 watt pulsed yag, fiber delivered in excellent condition. Energy share module can select either of the output fibers. Comes with 2-1000 micron fibers, 2 through the lens camera ready beam delivery heads and manuals. 3 units available.Price........ Call for pricing

7.5 ton water cooled chiller

used for the JK-701h laser systems above. These chillers can be used in a lab without heating the room temperature.

JDS Uniphase/LIghtwave  UV-610-fhg, 266nm 2 watt laser

Laser rail with power supply, low hours as per pictures, producing 7 watts of q-switched 532, and 2 watts of 266nm UV. Laser is in excellent condition with only 75 hours on doubler crystal. Price.....Call for pricing

Newport linear stage with rotary

in very good condition 24" stage with 3" rotary bolted on. Price......call for pricing

Newport Rotary stages models 

RV120CCHL-F(small), RV240HAHL(large). Excellent condition. Price.....Call for Pricing

Newport Rotary Stage model RV120CCHL-F

Excellent condition. Price........Call for pricing

Lumonics JK-701H 550 Watt YAG

Lumonics JK-701H 550 watt pulsed yag laser system producing over 550 watts output. With pulse rates up to 500 pulse per second, energy up to 70 joules per pulse, and pulse width of 500 microseconds to 20 milliseconds. Pulses can be shaped into 20 segments for preheat, or annealing. This unit was manufactured in 1997 with only 5739 hours use, most of which were idling. From the original owner the laser only ever had 2 lamp changes. Comes with full set of manuals, 10 meter 1000 micron fiber, camera ready  90 degree beam delivery head with crosshairs. This system is in gorgeous condition. Price.....................Call for Pricing

Big Sky CFR-200 cutting/hole drilling system

In perfect working order this Big Sky cfr-200 cutter has x, y, z, rotary, motion system for micromachining. With Parker stages, stepper driven-OS series, the travel is as follows: X=10", Y=6", Z=10", plus rotary 100% continuous. Comes through the lens viewing camera, manuals, RAM optical illuminator, spare parts. Shipping weight approximately #1500. Price.........Call for Pricing

Rofin-Sinar CW-020, 2000 Watt YAG

Rofin Sinar fiber delivered welder/cutter will deliver 2000 watts of power to the work-piece. There are 3 systems available. One is new, still in the crate and the other two are being disconnected for shipment this week.  All systems are in guaranteed excellent working condition. They run in the CW mode, pulsed mode, and the super pulsed mode for cutting. The cutting mode uses a 400 micron fiber with high pressure beam deliver head, whereas the welding mode uses an 800 micron fiber. We have many spare parts to support the laser systems, including rods, lamps, IGBFET's circuit boards, filters, diode packs, extra fibers, optics, beam delivery heads, shutters, flow switches, interlocks, resistors, capacitors, etc. Each system has a full set of manuals included. We can install this system if you require for a service fee. Also, we can integrate this laser with a motion system if needed. More pictures available upon request.  Price.........Call for Pricing

Lumonics JK-702H 350 Watt YAG

Lumonics JK-702H 350 watt pulsed yag laser system producing over 350 watts output. With pulse rates up to 500 pulse per second, energy up to 50 joules per pulse, and pulse width of 500 microseconds to 20 milliseconds. This system is set up for cutting parts, with the low divergence resonator. Also included is the ld resonator kit which allows you to select higher power higher divergence, or lower power with lower divergence. Pulses can be shaped into 20 segments for preheat, or annealing. This unit was manufactured in 2000 .  Comes with full set of manuals, can be configured with a cutting fiber and collimator or  hard optic cutting head, or camera ready  90 degree beam delivery head with crosshairs for welding. These systems are in gorgeous condition. 3 systems available. Price..........$Call for Pricing

JK-700 series lasers parts

Parts for JK-701, 701h, 702, 702h 703. Cabinets of new parts including Control panels, process shutters, safety shutters, lenses, mirrors, mounts, trigger boards, control boards, head boards, rods, flow tubes, pump chambers, reflectors, power supply lamp drivers, charging supplies, cooler parts, o-rings, relays, etc. Literally tons of parts, just call for your needs. Price...call for pricing

Lumonics 35 watt welder/cutter model MS-35

Lumonics ms-35ld pulsed welder/cutter, in excellent working condition. Comes with 400 micron fiber, weld head, power supply, controller and full set of manuals. Pulse width down to 100 microseconds, output to 3 joules/pulse, rep rate up to 120 Hz. This particular unit is set up for welding, but can be used for precision cutting with simply changing the rear mirror position and rotating the variable aperture in line. Price..............$17,500

Alpha 25 Ton, air cooled chiller model PCAL-SH-NF-25-460

The model NF-25-460 air cooled chiller is in excellent condition. It has a capacity of 88 kw, or 300,000 btu's per hour, with a 4 hp pump 46 gallons per minute at 65 psi pressure. This unit takes 45 amps per phase at 460v. Approximate shipping weight is 2800 pounds. Comes with manual, and is in excellent working condition. Price........Call for Pricing

New 25 Ton Carlyle compressor- Model Number 06EX265-360

This unit is new in the original box. Comes with installation kit, manual. Price.......Call for Pricing

Lasag KLS-111 YAG Laser Welder

Lasag 125 watt rated variable pulse width and rep rate, YAG welder with monocular beam delivery with cross hairs and illuminator for work piece.  Newly refurbished.  Price..............................$5,000

Lumonics 35 watt welder/cutter model MS-35

Lumonics ms-35ld pulsed welder/cutter, in excellent working condition. Comes with 400 micron fiber, weld head, power supply, controller and full set of manuals. Pulse width down to 100 microseconds, output to 3 joules/pulse, rep rate up to 120 Hz. This particular unit is set up for welding, but can be used for precision cutting with simply changing the rear mirror position and rotating the variable aperture in line. .........Call for Pricing.

AB Laser

model ILPM / same as #1 except mfrd. '97 / 6,000 hours use / 1 laser - XY is servo controlled, and has 16" travel. Z is manual / orig. cost $401k / book value $268k / excellent condition / asking price.....Call for pricing

Harris High Voltage supply

Rated 24,500 volts at 4.5 amps DC. Great condition. Comes with starter switch cabinet.  Price.......Call for Pricing 

Main Page

New Arrivals

Laser Systems

Optical Equipment

Laser Components


Test Equipment

Vacuum Equipment

Accessories

Contact Us

Contact Us (216) 990-0563
​** All equipment offerings are subject to prior sale **