Industrial Lasers







 
  • Lumonics JK 700/ Lumonics JK-706 1000 watt welder.  Very rare Lumonics JK-706 laser welder, rated 1000 watts will produce 1200 watts. Pulse widths from 500 micro-seconds to 20 milliseconds, with a max 105 joules per pulse, and a maximum rep rate of 500 pulse per second, and pulse shaping up to 20 segments. This system was manufactured for Westinghouse. The laser system is in excellent condition, and before de-commission was checked out by Lumonics. It comes with a 3 month warranty. This system has full set of manuals, schematics, beam delivery head, long armored fiber on reel Price.....................Call for Pricing

            


     
  • Micromachining system, MM5800 dual beam, by ESI-ESI MM5800 micromachining system employing two IPG 700 watt fiber lasers single mode, with twin Laser Mech beam delivery. This machine is capable of 2500 holes per second, was set up for drilling/cutting .030" (750 micron) aluminum with .012" (300 micron) holes. Can be used for any machining drilling or marking. Has twin cameras, both wide, and fine, with micron accuracy. System was never in service only used for some testing. Looks new with low hours. Cutting bed 533mm x 635mm, with "z axis of 40mm. See spec page below. Price...........call for pricing.







     

  • IPG 700 watt Fiber Laser model YLR-700-sm-New in the manufactures crate, IPG-700-sm. Below are some snap shots of the unit being removed from crating and vacuum bag packing, only opened to get pictures. Three units were manufactured 2008/2009 with delivery 2009 all with "0" hours and sealed in original crates, ready for immediate shipment. These lasers are rated at 700 watts average, single mode, and can be internally modulated up to 5 Khz. by hand controller which is included. All cables, accessories, controller, etc are included with each laser. Voltage requirements, 220, 11 amps. single phase, water cooled. Manual included. 7 lasers available. Price......Call for pricing



     


    Laserdyne 780 W/Lumonics JK-704 driller/cutter-
    Lumonics laserdyne 780 6 axis cutting/drilling system. Just removed from service. Has Lumonics beam director, comes complete with Neslab hx-750air cooled chiller. Extra pictures upon request. Price.......call for pricing





     
  • Laserdyne 550 W/Lumonics JK-704 driller/cutter-Lumonics laserdyne 550 6 axis cutting/drilling system. Just removed from service. Has Lumonics beam director, comes complete with Neslab hx-750air cooled chiller. Extra pictures upon request. Price.......call for pricing

     

     
  • Coherent/Deos Gem 100-Coherent Gem 100L, manufactured 2008, rated 100 watts, producing 125-130 watts, using a Synrad controller. Excellent condition, comes with manual, power supply, and controller fully operational. Power supply requires 220 volt single phase, no dc supply to mess with. Price.....call for pricing
     
     
     Spectra Physics UV-355 Tristar-1000-Spectra Physics diode pumped Tristar 1000 laser system producing 840mw, not optimized, but near spec. power. Q-switched 355nm laser system pictures taken in operation at 20Khz. Better pictures to follow. Unit is in very good condition.Price......call for pricing.

      
     




     A.E.C 8.5 ton air cooled chiller-In excellent condition with low usage, manual, 220 volt 3 phase. See Spec. page below. Price...call for pricing
     
        




    Coherent D-62, 80 watt, Co2 laserNew, unused-Excellent condition with manual, manufactured in 1996, new unused laser system. Price....call for pricing





     

  • Coherent D-64, 150 watt, Co2 laser -Good condition with manual, two available, one with controller, one without. Price....call for pricing





     
  • Coherent D-64, 150 watt, Co2 laser -Good condition with manual, two available, one with controller, one without. Price....call for pricing






    Trumph Haas H-703 D Laser-Has twin energy share module output. More info to follow. Price....Call for pricing



     
  • Yamabishi Auto Volt 25KW 3 Phase  power regulator- Yamabishi 25 Kw power regulator. Input from 170-230 volt, output 220 volt. Two units available.  Price...Call for pricing
     



    Synrad 48-2 CO2 laser-Comes with built in 120 vac. power supply, just plug it in the wall. Has less than 10 hours use on it. Excellent condition Price......Call for pricing




     

  • Lumonics JK-701h 550 watt Yag with twin energy share module-Just arrived 2 JK-701h 550 watt pulsed yag, fiber delivered in excellent condition. Energy share module can select either of the output fibers. Comes with 2-1000 micron fibers, 2 through the lens camera ready beam delivery heads and manuals. 3 units available. Price........ Call for pricing
     

     

    7.5 ton water cooled chiller-used for the JK-701h laser systems above. These chillers can be used in a lab without heating the room temperature.
  •  


    JDS Uniphase/LIghtwave  UV-610-fhg, 266nm 2 watt laser-Laser rail with power supply, low hours as per pictures, producing 7 watts of q-switched 532, and 2 watts of 266nm UV. Laser is in excellent condition with only 75 hours on doubler crystal. Price.....Call for pricing






     

  • Convergent Energy Gemini cutting system-Convergent Energy/Coherent Gemini 3 axis cutting system with off axis camera and crosshair generator. The system has 24" x 24" x 10", xyz travel with glass scale encoders by Aerotech for accuracy to .0001, and has a Coherent Diamond 84 laser rated 250 watts. Also in the upper laser compartment is the Convergent Energy water cooled spatial filter and circular polarization beam conditioning optics for superb cutting in either direction. On The "Z" axis, there is a micrometer for the fine focus adjustment. Laser power will be measured in the short future along with more internal laser and controller pictures. The system has a very nice cutting bed along with soot removal bottom suction connection to cutting bed. It has 2 separate inputs for either oxygen, or shop air, or whatever shield gas preferred. There is also a cabinet air removal to keep cabinet smoke free. Comes with manuals. 208 volt 3 phase operation. The system is in excellent condition. Price.........Call for pricing
     
           




    Newport linear stage with rotary-in very good condition 24" stage with 3" rotary bolted on. Price......call for pricing





    Newport Rotary stages models RV120CCHL-F(small), RV240HAHL(large). Excellent condition. Price.....Call for Pricing
     

    Newport Rotary Stage model RV120CCHL-F-Excellent condition. Price........Call for pricing
     




     

  • Lumonics JK-701H 550 Watt YAG -Lumonics JK-701H 550 watt pulsed yag laser system producing over 550 watts output. With pulse rates up to 500 pulse per second, energy up to 70 joules per pulse, and pulse width of 500 microseconds to 20 milliseconds. Pulses can be shaped into 20 segments for preheat, or annealing. This unit was manufactured in 1997 with only 5739 hours use, most of which were idling. From the original owner the laser only ever had 2 lamp changes. Comes with full set of manuals, 10 meter 1000 micron fiber, camera ready  90 degree beam delivery head with crosshairs. This system is in gorgeous condition. Price.....................Call for Pricing
     




     
  • Synrad 60-2 , 240 watt CO2 laser- Synrad 60-2 rf excited, sealed off tube co2 laser system including Laser head, two rf power supplies, dc power supply, power controller, Lasermec beam delivery. System has less than 1000 hours use. Excellent condition. We have the milling machine with software for cutting. This can be included, but the new owner must remount the laser head. The head was removed for another scientific use. Last measured, power output was at 285 watts. Can demo.  Price............Call for pricing


     
  • Big Sky CFR-200 cutting/hole drilling system--In perfect working order this Big Sky cfr-200 cutter has x, y, z, rotary, motion system for micromachining. With Parker stages, stepper driven-OS series, the travel is as follows: X=10", Y=6", Z=10", plus rotary 100% continuous. Comes through the lens viewing camera, manuals, RAM optical illuminator, spare parts. Shipping weight approximately #1500. Price.........Call for Pricing
     



     
  • Rofin-Sinar CW-020, 2000 Watt YAG- Rofin Sinar fiber delivered welder/cutter will deliver 2000 watts of power to the work-piece. There are 3 systems available. One is new, still in the crate and the other two are being disconnected for shipment this week.  All systems are in guaranteed excellent working condition. They run in the CW mode, pulsed mode, and the super pulsed mode for cutting. The cutting mode uses a 400 micron fiber with high pressure beam deliver head, whereas the welding mode uses an 800 micron fiber. We have many spare parts to support the laser systems, including rods, lamps, IGBFET's circuit boards, filters, diode packs, extra fibers, optics, beam delivery heads, shutters, flow switches, interlocks, resistors, capacitors, etc. Each system has a full set of manuals included. We can install this system if you require for a service fee. Also, we can integrate this laser with a motion system if needed. More pictures available upon request Price.........Call for Pricing


     
  • Lumonics JK-702H 350 Watt YAG -Lumonics JK-702H 350 watt pulsed yag laser system producing over 350 watts output. With pulse rates up to 500 pulse per second, energy up to 50 joules per pulse, and pulse width of 500 microseconds to 20 milliseconds. This system is set up for cutting parts, with the low divergence resonator. Also included is the ld resonator kit which allows you to select higher power higher divergence, or lower power with lower divergence. Pulses can be shaped into 20 segments for preheat, or annealing. This unit was manufactured in 2000 .  Comes with full set of manuals, can be configured with a cutting fiber and collimator or  hard optic cutting head, or camera ready  90 degree beam delivery head with crosshairs for welding. These systems are in gorgeous condition. 3 systems available. Price.....................$Call for Pricing
     


     
  • JK-700 series lasers parts- Parts for JK-701, 701h, 702, 702h 703. Cabinets of new parts including Control panels, process shutters, safety shutters, lenses, mirrors, mounts, trigger boards, control boards, head boards, rods, flow tubes, pump chambers, reflectors, power supply lamp drivers, charging supplies, cooler parts, o-rings, relays, etc. Literally tons of parts, just call for your needs. Price...call for pricing




     
  • Lumonics 35 watt welder/cutter model MS-35 - Lumonics ms-35ld pulsed welder/cutter, in excellent working condition. Comes with 400 micron fiber, weld head, power supply, controller and full set of manuals. Pulse width down to 100 microseconds, output to 3 joules/pulse, rep rate up to 120 Hz. This particular unit is set up for welding, but can be used for precision cutting with simply changing the rear mirror position and rotating the variable aperture in line. Price..............$17,500

      




     

  • Alpha  25 Ton, air cooled chiller model PCAL-SH-NF-25-460 -The model NF-25-460 air cooled chiller is in excellent condition. It has a capacity of 88 kw, or 300,000 btu's per hour, with a 4 hp pump 46 gallons per minute at 65 psi pressure. This unit takes 45 amps per phase at 460v. Approximate shipping weight is 2800 pounds. Comes with manual, and is in excellent working condition. Price........Call for Pricing


     
  • New 25 Ton Carlyle compressor- Model number 06EX265-360. This unit is new in the original box. Comes with installation kit, manual. Price.......Call for Pricing


    Lasag KLS-111 YAG Laser Welder - Lasag 125 watt rated variable pulse width and rep rate, YAG welder with monocular beam delivery with cross hairs and illuminator for work piece.  Newly refurbished.  Price..............................$5,000


     
  •  
  • Lumonics 35 watt welder/cutter model MS-35 - Lumonics ms-35ld pulsed welder/cutter, in excellent working condition. Comes with 400 micron fiber, weld head, power supply, controller and full set of manuals. Pulse width down to 100 microseconds, output to 3 joules/pulse, rep rate up to 120 Hz. This particular unit is set up for welding, but can be used for precision cutting with simply changing the rear mirror position and rotating the variable aperture in line. .........Call for Pricing.

        

     


     

  • AB Laser model ILPM / same as #1 except mfrd. '97 / 6,000 hours use / 1 laser - XY is servo controlled, and has 16" travel. Z is manual / orig. cost $401k / book value $268k / excellent condition / asking price.....Call for pricing

     

  • Harris High Voltage supply. Rated 24,500 volts at 4.5 amps DC. Great condition. Comes with starter switch cabinet.  Price.......Call for Pricing



    _________________

    anderr@earthlink.net