JK-700 series lasers parts- Parts for JK-701, 701h, 702, 702h 703.
Cabinets of new parts including Control panels, process shutters, safety
shutters, lenses, mirrors, mounts, trigger boards, control boards, head boards,
rods, flow tubes, pump chambers, reflectors, power supply lamp drivers, charging
supplies, cooler parts, o-rings, relays, etc. Literally tons of parts, just call
for your needs. Pictures to follow. Price...call for pricing
AEC 2-Hp. Chiller -
Model PSA-2 with 2 Hp compressor and 3/4 Hp circulating pump, manufactured 1997,
air cooled, excellent condition ....$ 2,000 each
(2 available)
Spectra Physics autocorellator model 409-In
very good condition, this scanning autocorellator will scan 80 ps + 40 ps shift.
Pulse-width resolution < .5ps. Price......call for pricing
4 x 5' x 8" Optical table-excellent condition. Price.......Call
for pricing
Oriel
Breadboard -
Oriel 30" wide x 6' long x 8" with 1/4-20
tapped holes on 1" centers, excellent condition. Price......Call for Pricing
Newport
3' x 6' x 8" optical table -Top in
excellent condition with 1/4-20 tapped holes on a 1" grid. Solid legs available. Price........Call for pricing.
Newport
4' x 5' x 12" optical table bolt on end section.-Top
in excellent condition with 1/4-20 tapped holes on a 1" grid. 2 20" solid legs
bolted on the far end support. Table is shown in the upside down position for
shipping. 6" from bolt end is a 20" x 20" factory cut-out. Price.....Call for pricing
Newport
10' x 4' x8" optical table with solid legs.-Top
in excellent condition with 1/4-20 tapped holes on a 1" grid. Solid legs
available, also 2 tables available. Price......Call for pricing
.
Newport XLB
series pneumatic isolation legs- Note, that only one set of "air legs"
are available with purchase of table top at an extra charge. The legs will go
with any one of our table tops.
TMC 5' x 12' x 1' thick table-- TMC 5' wide, 12' long, 1' thick optical
table with 1/4-20 tapped holes on a 1" grid. This table has an air isolated, six
legged frame under it that requires air pressure to float the system for
vibration free operation. Top is in very good condition with very few minor
scratches. Approx weight #3000.
Price....Call for pricing.
Newport EVIS -Electronic Vibration Isolation System-
24.5" x 37.5" x 11.75",
1/4-20 tapped holes on 1" centers in
excellent working condition. Typically used for mounting Atomic Force
Microscope. Vibration isolation to the piezo level.
Price......................Call for pricing.
Big Sky Erbium YAG laser head new- Big Sky model/P# 10228100P,
new
Koolant Kooler model KV-3000-
Rated 3 hp, with 1.5 hp circulating pump, 480
volt @ 8.75 amps. Unit is in good working condition. Price.....Call for
Pricing
Hewlett Packard 5500C, 5517C Interferometer heads- Three HP 5500C laser
heads and 1 5517C laser head. Cables available.......Price................Call
for Pricing
Spectra Physics / Lasermetrics Harmonic Generators -
Various types in good condition.
Call for Pricing.
AEC model DLA-3 chiller / w/ digital control / rated 9.3 KW @ 13 degrees C / about 10.5 KW
at 20 degrees C / water-cooled / special large pump (1.5 hp) / 440V three-phase power / mfrd. '87 / many nice features / very good condition / can demo.....$800
Laser Drive Model LDI 830 Diode Supply, and SDL 800 M - 2000 ma
supply -..................Call for Pricing.
SDL-822 diode driver--
SDL-822, 15 amp diode driver with TE cooler, excellent condition.
Price....Call for pricing.
SDL-822 diode driver-- SDL-822, 15 amp diode
driver with TE cooler, excellent condition. Price....Call for pricing.
Lumonics Fiber beam delivery heads
- Lumonics fiber beam delivery heads with 1" camera "through the lens" viewing
port. These units are ready for a camera to be mounted with the x-y adjustable
1" mount for the camera. Also in stock are 2-5 meter 1000 micron
fibers for JK-701. Excellent condition........................Call
for Pricing
Opto Power
810-808 nm Fiber Diode with Controller - Model
OPC-A015-810-FCPS, mf'd. 1997 with 95 hours use. Unit in excellent
condition with output over 20 watts from the fiber. SMA connector, temperature
management and power controller with remote pendant control. 4 available-
Price...................$3,000
General Photonics YAG Laser Head -Two-43 YAG Laser head with Cleveland Crystals Q-switch, pump chamber, rod
and optics, ready to go in excellent condition - just add power supply. (3
available) Price.......................$1,200
Quantronix 117 pump chamber-This pumping chamber is brand new
and identical to the q-117 chamber other than the water inlet and outlet is on
the bottom. New lamp + jacket; new rod + jacket; new reflectors.....Price.................$1500
Laser Photonics YAG Laser Head and Water Cooler -
Q-switched rated 150 mj/pulse @ 10 ns @ 20 hz
with water circulator, hoses, cables, just needs power supply. Head in
excellent condition. Price.....................................$2,500
SU-256LD InGaAs Photodiode array with T/E cooling. Spec
pages displayed. Nearly 2.5 micron sensitivity wavelength. Four brand new
units available with manual. Price....Call for Pricing
Lasermetrics LM-5016 Pulse Timing Unit Driver and Q-Switch -
Krytron fired. Price..............................$2,500
Lasermetrics LM-8601 Q-Switch Driver - Krytron fired with
time delay generator. Price..................................$1,750
Coherent Optics - Hundreds of new Coherent Optics for various
systems in stock. Inquire with part numbers. Call for Pricing.
Lasag -
Lasag Fiber and 90 degree camera ready beam
delivery head. Fiber is new in the original box, beam delivery head is
slightly used, in excellent condition. Price..................$3,500/set, call for individual pricing.
Hamamatsu Phototube Model R1193U-01 -
New in the original box..........Call for
Pricing
Control Laser Q-Switch Driver...............$500
New Focus model V8801 Multi Axis Pico Motor Driver
w/ 2 model V8051 Pico Motor Stages and model V8620 Control Pendant.
Price................$1,500
ILX Lightwave 3722B w/ TE cooler controller / range: 0-200 and 0-500 mA (selectable).....$2,000
ILX Lightwave Laser Diode Driver including TE cooler -
Model 3744B, with TE controller, IEE-488
controller port, 4000ma, excellent condition. Price......................$2,000
Laser Diode Driver 200 amp,- Tutcore Electronics Model 200A manufactured
2000 with RS-232 for control, 1200 watt 120V. Price................$2,000
Cassegrain Thermal/IR Telescope
- This telescope has a 7" diameter main mirror and
a gallium-arsenide output lens of about 2" diameter. This was manufactured
for Raytheon and comes in a nice carrying case. It is made for optical
table mounting and has a focus adjuster on the front (top).
Price...................$2,400
Melles Griot 532nm Telescope -
Up-collimating precision telescope for 532 nm. New in carrying case.
Appears to be 20 x, but will confirm. Input aperture approximately 5 nm.
Output aperture 25 nm. Comes with calibration and specification sheets.
Price..............$1,100
Spectra Physics dye pumps and dye laser motor scan controllers (several of each available)
Dye pumps.....$800 ea.
Controllers.....$900 ea.
Thyratrons - Many styles and sizes, new and used. (over 100
available) Call for pricing.
Multiple manual adjustment stages (call for details, many available) Melles Griot
X-Y-Z compound adjustment fiber alignment stages / Newport X-Y-tilt stages.....Call
for pricing
Alexandrite laser rod / 5mm x 146mm long, AR coated at both
ends / new in box price.....$1,000
Choppers with
or without drivers.....Call
for pricing
Procon PD-2 with motor clamping rings /
brand new in the box / stainless steel / 1/2" height inlet/outlet / 3.6 gpm /
5 available).....$100
JK Lumonics Power share and time share modules -
many modules both time and power share along with
600 micron fibers available. We can configure the modules and outputs to
your needs. Call for pricing.
Three way power
share for JK-700 Series laser.....$2,500
Two way time
share for JK-700 Series laser / pneumatically operated.....$2,500
ESI YAG Pump Chamber -
New lamp and rod Model 3800....$1,000
.JPG)
.JPG)
